3D Printer Explainer Video

Submit Audition/Proposal on this Project
Rate this Project

Project Main Details

3D Printer Explainer Video 
ZD2853742
This is an explainer video for a startup that makes 3-D printers. It is intended to be seen on the company's website by people who need instructions on how to use their products. The tone should be friendly, helpful, patient.
The script attached in only a small portion of the total script. The final video will run about 8 mins. 
2017-06-15 00:48:17 GMT
2017-06-18 09:00:00 (GMT -08:00) Pacific Time (US & Canada) 
Yes (click here to learn more about Voice123's SmartCast)
Closed
16
14
0 direct invitation(s) have been sent by the voice seeker resulting in 0 audition(s) and/or proposal(s) so far.
Voice123 SmartCast is seeking 50 auditions and/or proposals for this project (approx.) Invitations sent by SmartCast have resulted in 16 audition(s) and/or proposal(s) so far.

Project Parameters

The Voice Actor should be located in:
Fixed - USD 200
Training, business presentations, sales, and web sites
Via Internet: N/A
1 MINUTES
English - USA and Canada
Not defined
Young Adult Female OR Middle Age Female
• Audio files must be delivered via email OR
• Audio files must be delivered via FTP/Dropbox/Google Drive/cloud
There are no special pre-, post-, or production requirements for this project.
Not defined
This is a non-union project

Script Details

Yes
N/A 
This video will cover:
• Unboxing
• Getting to know Robo R2
• Initial set-up
• Connecting to Wi-Fi
• Software update
• Calibration
• Loading filament
• Test print
• Removing the test print
• Printing from USB, and
• Next steps for total connectivity
To unbox Robo R2, start by pulling out the Robo R2 box from the brown shipping box.

Now, remove the three clips by pinching and pulling them out.

Once they are out, the top box will easily come off.

Using scissors, cut the zip tie from the Plexiglas door.



Remove the blue tape on the accessories box. Then, pull out the accessories box.

Remove the top foam piece. Then, remove the cardboard that’s inside the printer. Finally, remove the last foam piece underneath the print bed.

Keep in mind that the information highlighted in this video is also available in the Robo R2 quick start guide inside of the accessories box.

Next, remove the four protective gantry clips by pushing them over sideways with you thumb on the clip’s round area — do not pull straight up.

Then, cut the rest of the zip ties that hold the gantry together.

Remove the blue tape on the spool holders. Also, remove the protectors on the Plexiglas door.

Now, remove the rest of the blue tape that’s inside the printer.

And finally, using both hands, locate the hand inserts on the bottom of the printer and carefully lift it from the bottom foam box. 
Please note that you should only use the script or your recording of it for auditioning purposes. The script is property, unless otherwise specified, of the voice seeker and it is protected by international copyright laws.

Voice-Seeker Details

117507
Sign in to display the company name (if applicable)
2017-01-03
4

1


Voice123 Team Comments

Voice123 consultations with this voice seeker regarding this project and/or other projects by this voice seeker, via phone, chat, and/or email.


unchecked This project - phone.

unchecked Previous projects - phone.


unchecked This project - email or chat.

unchecked Previous projects - email or chat.



Note: Voice123 strives to establish the legitimacy of all projects posted. However, Voice123 subscribers and users are responsible for confirming information stated by prospective voice seekers, agents and/or clients. Voice123 subscribers and users assume all liability for use of any information found through Voice123, or any of its publications.

This page contains the most important details of this project. If you find the information on this project inaccurate or inappropriate, please let us know by contacting us.

Submit Audition/Proposal on this Project