This page contains the most important details of this project. If you find the information on this project inaccurate or inappropriate, please let us know by contacting us.
Submit Audition/Proposal on this Project
Rate this Project
Invitation Inbox
Project Main Details
Male voice needed for an e- learning course
LTK910894184X
90 minute e-Learning course that shows people how to use a manufacturing software. Tone is to be extremely converstaional. Auditions that sound anything remotely close to a commercial will not be considered. Tone of the audition should sound like you are telling a buddy how something is done....not presenting.
Budget USD$300 Dec 15, 2006 17:52:44 (GMT -05:00) Eastern Time (US & Canada) Dec 22, 2006 00:00:00 (GMT -05:00) Eastern Time (US & Canada) No (click here to learn more about
)
Closed
85
85
0 direct invitation(s) have been sent by the voice seeker resulting in 0 audition(s) and/or proposal(s) so far.
Budget USD$300 Dec 15, 2006 17:52:44 (GMT -05:00) Eastern Time (US & Canada) Dec 22, 2006 00:00:00 (GMT -05:00) Eastern Time (US & Canada) No (click here to learn more about
)
Closed
85
85
0 direct invitation(s) have been sent by the voice seeker resulting in 0 audition(s) and/or proposal(s) so far.
Project Parameters
None
Flexible - USD 300
Videogames
Not defined
English - North American
Not defined
Young Adult Male
Not defined
There are no special pre-, post-, or production requirements for this project.
Not defined
Not defined
Script Details
Yes
"Voice123 Team Note: The voice seeker has been adviced that the budget may be a little low for the project. Please do not answer if you consider this budget to be too low for you."
I’ll go ahead and right click, and Select “Insert 2.5 (two-and-a-half) Axis EDM Feature”. I’ll make sure the feature type is set to Open Profile and select the sketch we just created to define it. Pay attention to the red arrow in the graphics area. Remember, the arrow must face away from the finished part. You have the option to flip the direction of the cut if necessary. Keep in mind that this option may at first appear grayed out, to activate it, you must first highlight the Open Profile from inside this window. Now when I click the option you can see the red arrow update in the graphics window.
For the end condition I’ll choose Up to Stock in both directions... click Insert… and exit the Feature Definition box. Once again the feature tree is updated, and the Open Profile feature is added under the second Part Setup.
At this point I we should be done adding features. I’ll generate an Operation plan by right clicking on the Open Profile feature… Then generate Tool paths by right clicking on the corresponding Operation
And Finally, I’ll run the simulation…
Notice that the cutting wire switches orientation to match our second Part Setup.
To finish up, I’ll remove the leftover chips…And the result is exactly what I was looking for.
Budget USD$300
I’ll go ahead and right click, and Select “Insert 2.5 (two-and-a-half) Axis EDM Feature”. I’ll make sure the feature type is set to Open Profile and select the sketch we just created to define it. Pay attention to the red arrow in the graphics area. Remember, the arrow must face away from the finished part. You have the option to flip the direction of the cut if necessary. Keep in mind that this option may at first appear grayed out, to activate it, you must first highlight the Open Profile from inside this window. Now when I click the option you can see the red arrow update in the graphics window.
For the end condition I’ll choose Up to Stock in both directions... click Insert… and exit the Feature Definition box. Once again the feature tree is updated, and the Open Profile feature is added under the second Part Setup.
At this point I we should be done adding features. I’ll generate an Operation plan by right clicking on the Open Profile feature… Then generate Tool paths by right clicking on the corresponding Operation
And Finally, I’ll run the simulation…
Notice that the cutting wire switches orientation to match our second Part Setup.
To finish up, I’ll remove the leftover chips…And the result is exactly what I was looking for.
I’ll go ahead and right click, and Select “Insert 2.5 (two-and-a-half) Axis EDM Feature”. I’ll make sure the feature type is set to Open Profile and select the sketch we just created to define it. Pay attention to the red arrow in the graphics area. Remember, the arrow must face away from the finished part. You have the option to flip the direction of the cut if necessary. Keep in mind that this option may at first appear grayed out, to activate it, you must first highlight the Open Profile from inside this window. Now when I click the option you can see the red arrow update in the graphics window.
For the end condition I’ll choose Up to Stock in both directions... click Insert… and exit the Feature Definition box. Once again the feature tree is updated, and the Open Profile feature is added under the second Part Setup.
At this point I we should be done adding features. I’ll generate an Operation plan by right clicking on the Open Profile feature… Then generate Tool paths by right clicking on the corresponding Operation
And Finally, I’ll run the simulation…
Notice that the cutting wire switches orientation to match our second Part Setup.
To finish up, I’ll remove the leftover chips…And the result is exactly what I was looking for.
Budget USD$300
I’ll go ahead and right click, and Select “Insert 2.5 (two-and-a-half) Axis EDM Feature”. I’ll make sure the feature type is set to Open Profile and select the sketch we just created to define it. Pay attention to the red arrow in the graphics area. Remember, the arrow must face away from the finished part. You have the option to flip the direction of the cut if necessary. Keep in mind that this option may at first appear grayed out, to activate it, you must first highlight the Open Profile from inside this window. Now when I click the option you can see the red arrow update in the graphics window.
For the end condition I’ll choose Up to Stock in both directions... click Insert… and exit the Feature Definition box. Once again the feature tree is updated, and the Open Profile feature is added under the second Part Setup.
At this point I we should be done adding features. I’ll generate an Operation plan by right clicking on the Open Profile feature… Then generate Tool paths by right clicking on the corresponding Operation
And Finally, I’ll run the simulation…
Notice that the cutting wire switches orientation to match our second Part Setup.
To finish up, I’ll remove the leftover chips…And the result is exactly what I was looking for.
Please note that you should only use the script or your recording of it for auditioning purposes. The script is property, unless otherwise specified, of the voice seeker and it is protected by international copyright laws.
Voice-Seeker Details
Voice123 Team Comments
Voice123 consultations with this voice seeker regarding this project and/or other projects by this voice seeker, via phone, chat, and/or email.
This project - phone.
Previous projects - phone.
This project - email or chat.
Previous projects - email or chat.
Corporate web site for this voice-seeker confirmed by Voice123
Note: Voice123 strives to establish the legitimacy of all projects posted. However, Voice123 subscribers and users are responsible for confirming information stated by prospective voice seekers, agents and/or clients. Voice123 subscribers and users assume all liability for use of any information found through Voice123, LLC, or any of its publications.
